• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your cat go in and out whenever they want without needing to let them in or out. They also can help to prevent your cat from toileting inside the house.

It is much easier to put a cat flap fitters flap on a Upvc panel than one made of glass however, you'll require some expertise and correct tools.

Measure the Door

The installation of a cat flap in a front door could be difficult however, so long as the cat flap is the correct one and you follow the guidelines, it shouldn't be too difficult. We will help you draw the shape and then use an jigsaw to cut out the door's area. Then we will finish the job by attaching the cat flap. This will ensure that the flap stays in place and shields the door from wind and rain damaging the door.

To determine the size of the cat flap that you need, measure the width of your pet. This will ensure that the flap is large enough to let your pet go inside and out of the house without having to open and close the door every time, yet small enough to stop them from moving too far in either direction.

If your kit comes with a drawing showing where to drill then you can put it on the door and then draw a pencil around it. If your door has moulding or a sill at the bottom, make sure you leave enough space between your cat and these elements.

Put on your eye protection as well as a dust mask, and using a jigsaw, begin cutting according to the lines you've drawn in. Don't press the blade too hard as this could make it cut faster than you would like it to. If you own a set square then use it to check that you are cutting correctly and to make sure the hole is in a rectangle. Once you are satisfied with the shape, you can begin to take off the remaining door material.

Draw a Line

The Fitting cat flap in upvc door panel flap allows you to let your pet in and outside without worrying about unwanted visitors or unwelcome gifts. It also stops draughts and helps to keep the temperature in your home steady. Installing a cat flap on your door might seem difficult to those who haven't done it before. A lot of people will hire an expert carpenter or joiner to complete the work. While this is definitely an option, it's possible to complete the task yourself if you own the appropriate tools and follow the instructions with care.

Although this is much simpler with a timber door, it is still possible to do this in uPVC doors, though you need to be very careful to avoid damaging the doors, as this can end the warranty. The first step in the process is to measure the door and ensure that it will accommodate the new cat flap. If you have an ordinary uPVC panel it's easy. However when your door is composite or a different type of door, you may have to be more cautious.

Next, you will need to determine the belly height of your cat. This is the height from the floor to the lower part of the cat's stomach, and you'll need to find a spot on the door that will be within the range your cat can comfortably pass through. Once you've figured out the measurements, you'll be required to mark the space with a spirit-level and a pencil so you know the hole will be suitable for your cat.

After you have marked the area, it's time to cut the hole. You will need to use the jigsaw, and it is important that you take your time to ensure that the cuts are smooth and straight instead of uneven and rough, since this could damage your door. Wear safety glasses and a dust mask while working with the Jigsaw. Inhaling sawdust is dangerous for your health. Once you've finished cutting the hole, you'll require sandpaper for smoothing the edges so that the cat flap is easily inserted.

Cut a Hole

Installing a cat flap into an existing door panel or double glazing sealed unit can be quite difficult. If you're not proficient in DIY, it's best to employ an expert to do the job for you. A botched job could not only be unsightly, but also pose security risks. It could allow cold air in when the cat is outdoors and hot air out when the cat is inside.

The first thing to do is draw the location of the hole in the door with an eraser and an ax level. This will ensure that it is positioned and that it runs parallel to the other components of the door. Make sure you have some sandpaper on ready to smooth any edges.

Once the line has been traced, you must cut the hole using a jigsaw, remember to wear any safety equipment for working with a power tool. If you are worried about the sound produced by the jigsaw, consider buying a cordless version which is quieter and more user-friendly to use.

It is best to only remove the material that is required to make the cat flap. A little bit of extra material will be required for the thickness of the wall of the flap but removing more than that could cause issues and cause damage to the door frame.

If the door is made of upvc and has a metal panel or frame, it may interfere with the microchip flap. In this case you'll need create an over-sized hole to ensure that the metal doesn't touch the walls of the flap.

If you're planning to install a cat flap in windows made of double glazing cat flap-glazed or upvc with metal frames you'll need to talk to a specialist. They will provide you with a new piece of glass that has the hole that is already designed for the cat flap. This will be less expensive than trying to fit the flap into an existing pane that was not made specifically for this purpose.

Fit the Flap

Cat flaps allow your pet the freedom to come and go anytime they want and let them relax in the home whenever they'd like. However, if you have a uPVC door it can be difficult to fit an animal flap, especially if you don't own a glass pane that can be cut to accommodate one. If you're willing to purchase and install a new half-glazed uPVC panel, then it's possible to fit a cat flap fitting near me flap to these doors. It's not a matter of drilling an opening in the door. You'll also need to perform a few steps to ensure it's safe.

A composite, uPVC or GRP door panel is usually composed of a thin plastic skin that is bonded to an insulating polystyrene core. The material is fairly fragile and care should be taken when cutting through it to avoid damaging. This type of door usually comes with a template drawing which you can use as a guide to cut the hole into your door.

After you have marked out the opening in your front door, it is time to put in the cat flap. You can choose from a variety of models, ranging from simple push-button flaps to ones that are microchip-activated and allow your pet in. No matter which type of cat flaps you select it is essential that your cat is able to utilize the flap with ease without getting stuck in the rain.

It is a good idea to choose circular fittings instead of a square one, as circles are more securely cut into the door glass. This is because square holes leave the glass vulnerable to cracking when a drill is used on it. It's also a safer option as you don't risk having to drill into toughened glass that might break and cause injury to your pet or family members. This is particularly crucial if you have elderly or children in your home who could be hurt by glass fragments.