• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

repairing double glazing windows Glazing Door Lock repairs double glazed windows

Have your uPVC window or door mechanism deteriorated? Perhaps the door or window handles don't meet up properly or are difficult to use.

You'll be wasting energy in the event that your double-glazed doors fail to perform as they should. This increases the risk of burglary. Owen the Locksmith can fix your door lock for an affordable price.

Snapped Key

If a key is snapped off inside the lock, it can be extremely frustrating. It also poses a security risk, as the door might not lock and could leave you open to intrusion. There are a few easy fixes you can try to repair the issue and get your door working again.

Remember to remain calm. If you panic you may end up pushing the broken key piece further into the lock.

Then spray WD-40 or a different penetrating oil into the lock to make the broken piece to slide out more easily. You can also use the screwdriver to break up any pieces that are stuck. If you have a piece of the key that is stuck out, grab it with a paperclip or another thin metal object and pull it. Both methods are effective, but you need to be careful not to push the damaged key piece further into the keyway.

Some paperclips come with grooved edges which can be used as hook extractors. Jigsaw blades are also well for this. If you don't have any of these then you can bend a hook with needle-nosed pliers. Additionally, a pair of tweezers is a good way to grasp and remove the remaining bit of the broken key.

If you can't get the broken piece of the key out, you can try using a lock de-icer. It's available in many hardware stores and is used to freeze any moisture present within the lock.

If none of these solutions seem to work, it could be time to consult a locksmith. Fitlocks experts can quickly fix problems with uPVC door locks and mechanisms that have snapped keys as well as broken handles. They can also reconfigure your double glazing door mechanisms to make them easier to operate. Get a double glazing repair double glazing with us online or give us a call to discuss your needs.

Broken Cylinder

A broken cylinder is an extremely risky security issue. Luckily, it's an easy repair double glazing for a professional locksmith to complete. To fix the cylinder, a locksmith will need to tap it. They can do this with a hammer or other tool, but the most efficient way is to use a long match or piece of wire. Then, position the end of the match or wire in the keyway. After this, the locksmith will strike the lock to crack it open. This is much safer than using a hammer that can harm the lock.

The most frequent cause of cracks in the cylinder head is overheating. This can occur when the cylinder block and head are made of various metals, including cast iron and aluminum. Different metals will be heated and cool at different rates. This can cause localized hotspots to expand faster than the rest of the cylinder.

Another possible cause for cracks in cylinders is corrosion. If the cylinder head and the block of the cylinder are not properly maintained, this can lead to rusting or corrosion and cause them to expand at a greater rates than they ought to. This could lead to cracks over time.

If your uPVC window or door lock is stiff or requires lots of pressure to turn, this could be due to many things. A malfunctioning locking mechanism, misalignment, or an old handle are the most common causes of this issue.

This is a simple and affordable fix that the majority of double glazing owners can accomplish. A professional locksmith is able to solve the issue within one hour of arriving at your property. They can repair the locking mechanisms, or change the window handles and change the gearboxes, depending on the specific requirements of your home. A professional locksmith will always be able to advise you on the most cost-effective solutions for your home. They can recommend upgrading to 3 Star TS007 Euro Cylinders which provide an additional layer of protection from burglars. It's a small amount to enjoy the peace of mind that comes from knowing that your uPVC door is secure.

Broken Handle

It's not a surprise that window handle locks can break. They have complex mechanisms that become less effective over time. If yours is damaged it's difficult to pinpoint the cause of the issue. Make sure you fix it properly.

Fixing your broken handle, whether it's an internal latch or locking mechanism can increase the security of your uPVC door and prevent draughts. It could be costly to replace or repair your handle incorrectly and it could also harm the frame and lock of your door.

Screwdriver When the window is open remove the screw that holds the handle. It should be located on the inside face of the back plate, which is usually covered by a screw cover for aesthetic reasons. Be sure to not lose any of the internal components inside the handle, like the levers or plates on either side of the spindle. Ideally, keep these in the same place so you can re-install them if needed.

Then, using a second screwdriver loosen the screw that connects the handle to the spindle on the back. Once the screw is loose, you can remove the handle and take out the broken spindle. Replace it with a new one, making sure it's the same length as the old one (you can usually find these on the internet or at hardware stores) and screw it securely into place. Do not tighten the screw too much because this could damage the handle and the window frame.

Close the handle and try it. It should operate smoothly, and you will be able open your window after a few times.

While you're working on the handle, make sure to make sure your uPVC windows are closing properly. If they don't close correctly, you could encounter damp or draughts in your home. It could also affect the energy efficiency of your home. A local window company, like Core Sash Windows, will be capable of adjusting the hinges on your window frames so they are able to shut properly.

Broken Spindle

It is more likely for the spindle to break rather than the handle. This is particularly common with uPVC tilt-and-turn windows. These kinds of windows require a handle that is a lock mechanism that is located in the window frame. The handle is attached to a centre rod that is then activated by a series of cams that look like mushrooms, they lock into window frame keeps. If the dead latch mechanism is not able to open when the handle is turned it is likely that the spindle has broken and this could be a very frustrating issue.

There are ways to fix this issue. A good locksmith can quickly and efficiently fix this problem. They can disassemble the window handle by using a tool to remove the wheel part of the mechanism where the spindle goes. This can be done without causing any damage to the handle or causing other damage to the window frame.

After removing the wheel, the technician can examine the spindle to determine the cause of the break. This involves breaking down the spindle into its component parts and carefully recording their general condition as well as any specific areas of damage or excessive wear. This procedure is usually done in a clean environment by skilled technicians.

The next step is to clean the damaged spindle, this will remove any dirt or debris that could be hindering its normal functioning. After that, the spindle can be repaired or replaced. If the technician is replacing the spindle he can use a dowel that is the same size to the original. He will then make holes in the same way into both pieces. This ensures that the new spindle has a precise fit with the handle.

If the damaged spindle can't be repaired, it could require replacement. Home centers offer generic replacements but if the style of your window is rare then it is necessary to find a woodworker or cabinet maker who can duplicate the exact component for you. Once the spindle has been installed, it is connected to the handle. Line up the screw holes on the handle to the screws already in the frame. Once the handle is firmly in place, you can use your uPVC windows.